Innovative cooling concept reduces maintenance costs

28 Jan 2020

New situation-specific cooling of thermoforming tools reduces wear

It's annoying when a thermoforming tool wears out quickly, the service life is too short, the maintenance and resulting costs are too high. This can often be traced to the tool cooling. The current systems usually inaccurately regulate and record the temperatures. Internal temperatures are the key for wear of fall-through cutting tools.

 

The specialists at Kiefel, Freilassing, have taken on this problem and developed a solution. The new tool cooling system is fully automatic and sensor-controlled. This innovation has an especially positive effect on tool life and product quality. The tools utilize two separate cooling circuits for the upper and lower tool and an extended sensor system for optimum control. Two pumps and mixer valves supply the two circuits with cooling water; the integrated temperature control ensures optimal tool protection. Start automation is sensor-controlled, completely eliminating overshooting of the lower tool.

 

The critical moment

The production start of the machine is the critical moment for the temperature regulation of the tool halves. The cooling integrated in the tool must be capable of compensating heat output that can rapidly rise by up to 40kW. The result: uneven temperature distribution within the tool and a high temperature difference between the two tool halves. The very tight manufacturing tolerances of under 3 μm mean that a temperature difference of only 2° C leads to expansion of the material, causing abrasion and, as a result, wear on the tool. The consequence is obvious: The cutting components of the tool have to be reground prematurely. This represents costs of several thousand euros.

Previous attempts have failed to satisfactorily solve the problem. Time and again it has been proven: Higher heat input to the lower tool than to the upper tool may lead to the lower tool needing more cooling power than is available. Its temperature rises. The upper tool can maintain its temperature due to the lower heat input. The temperature-induced material expansion of the tool halves means that the gap between the two tool halves shrinks and wear increases. This phenomenon also occurs when the customer's cooling device is subject to rapid, large temperature fluctuations in the provided cooling water.

 

The solution

Kiefel has tackled this problem with innovative situation-specific tool cooling. It automatically detects incorrect states and compensates for them e.g. by increasing the temperature of the upper tool when the lower tool temperature increases. The new cooling concept avoids temperature differences between the upper and lower tool.

 

This is made possible by two different pumps, which supply the two halves of the tool continuously and independently of each other with the maximum possible flow of cooling water. This trick allows the temperature gradients within the tool halves to be kept very low. The temperature of the cooling water is controlled by two separate mixers in the return of the machine, which are controlled by the PLC control. For optimum control, the current temperature values of the tool, the flow and return of the two mixers and the cooling water temperature provided by the customer are cyclically input into the control system. The volume flow in the cooling circuits always remains constant. This control principle constantly provides the optimum cooling water temperature and adjusts the tool temperatures quickly and accurately to the process. Fixtures in particular variable speed pumps or chokes for influencing the flow in the cooling circuits are not installed!

 

Focus on functioning

The cooling system distinguishes between four different states:

 

Standby:

In standby, the tool temperature is slowly brought to the temperature desired by the operator and then maintained. Ideally it should be 20°C. In order to avoid unwanted condensation on the tool surface, a temperature of > 20 ° C in standby mode is also possible in tropical countries.

 

Production start:

This is the most critical situation. At startup, the flow temperature of the cooling water to the tool is initially reduced to prevent excessive heating of the tool. The temperatures and states are compared with the target values at very close intervals, to keep the lower tool temperature below the upper tool temperature. This can lead to minor fluctuations in the tool temperature. To stabilize the process, it is automatically switched to the production state depending on certain criteria.

 

Production:

During production, the set target values are adjusted as far as the customer cooling water flow temperature allows. The temperatures of the two tool halves are adjusted and regulated independently of each other at all times. Thus, both tool halves always remain within the tolerance window, guaranteeing a long tool life.

 

Production stop:

When the machine is stopped, the cooling capacity is lowered tool-specifically. This prevents excessive cooling and associated condensation on the tool.

 

Simple and user-friendly

The Kiefel developers focused on yet another aspect: Operation of the new cooling had to be simple and user-friendly.  They succeeded! The cooling activates automatically and only one important value needs to be input by the operator - the desired tool temperature. [see figure 1]. The constant tool temperature at the start of the machine - even with difficult materials - ensures reliable quality from the start.

Kiefel successfully lowered tool maintenance costs with enhanced precision sensor technology and a new, innovative control concept, giving its customers a clear advantage.

Kiefel KMI 2.0 – The cooling activates automatically and only one important value needs to be input - the desired tool temperature.
Kiefel KMI 2.0 – The cooling activates automatically and only one important value needs to be input - the desired tool temperature.
Two pumps and mixer valves supply the two circuits with cooling water for the upper and lower tool.
Two pumps and mixer valves supply the two circuits with cooling water for the upper and lower tool.
The Next Generation of the SPEEDFORMER KTR 5.2 Speed Cupforming System
The Next Generation of the SPEEDFORMER KTR 5.2 Speed Cupforming System

Downloads

Our PDF documents for more detailed information.

More News

News & information from Kiefel

Upside-down suction process ensures a more even fiber distribution
13 Jul 2020

Fiber Thermoforming: Looks like plastic – made of paper!

They look as if they were made of plastic: food containers and packaging, medical articles, inlays for mobile phones and other high-quality electronic devices, plant pots, even drinking cups and their lids. But looks can be deceptive. Fiber...
Find out more
07 May 2020

New CTO - Kiefel strengthens its management

Stefan Moll is the new CTO – Focus on medical engineering
Find out more
16 Apr 2020

Thermoforming meets fiber

Plastics Know-How for Fiber Processing
Find out more
28 Oct 2019

Mono-material hot fill cups out of foamed PET

Find out more
Kiefel is a market leader in the design of machines for blood bag production.
25 Oct 2019

Kiefel: Safe packaging for the elixir of life

According to World Health Organization (WHO) 2019 data, approximately 117.4 million blood donations are collected worldwide each year. The demand for blood bags is high. According to the Federal Centre for Health Education (BZgA) alone, clinics in...
Find out more
22 Oct 2019

Plastic is a valuable source

Kiefel Packaging introduces the Design for Recycling programme, in which products are “rethought” together with the customer. The main objective: How to make their plastic products more sustainable..
Find out more
Kiefel Packaging has re-engineered the egg tray: recycled post-consumer PET.
02 Oct 2019

Post-consumer recycled PET egg tray

Kiefel Packaging is showcasing a post-consumer recycled PET egg tray. 
Find out more
The Next Generation of the SPEEDFORMER KTR 5.2 Speed Cupforming System
30 Sep 2019

The Next Generation of the KTR 5.2 Speed Cup-forming System from Kiefel at the K 2019

KTR 5.2 Speed of KIEFEL: Integrated Optimization for more Quality and Efficiency! Enhancing production and efficiency - the thermoforming specialists at KIEFEL GmbH, Freilassing, have focused on the continued development of the tried-and-tested...
Find out more
Kiefel Packaging lauches a trim-in-place performance tool
25 Sep 2019

Kiefel Packaging launches future proof Performance Tool at K-Show

Kiefel Packaging added a brand new performance tool to the Bosch Sprang Thermoforming ToolsTM-series. A trim-in-place solution designed for maximum performance in 24/7 operation. Join the launch at the Kiefel booth during the K-Show, Hall 3, Stand...
Find out more
On more than 1500 m2, the education center offers Kiefel trainees and employees a modern training environment.
23 Sep 2019

New Kiefel Education Centre: On the pulse of time - future-oriented learning in a modern environment

KIEFEL GmbH, Freilassing, stands for high-quality machines and outstanding service. That would not be possible without the dedicated and well-trained staff. The new Kiefel training center was officially opened on September 20, 2019. It offers not...
Find out more